OS support all operating systems. Port TCP. Device support all devices. Setup Guide. OS support all operating systems on Linux required to install additional packages. Port UDP. Device support supported by most devices routers require additional configuration. The best choice — allows to ensure high security, speed and reliability.
What's the best free way to do it? Thanks, Udi. Improve this question. Adam Matan Adam Matan What operating system are the PCs running? XP and Vista, but I'm looking for a general solution. Add a comment. Active Oldest Votes. Improve this answer. Wesley Wesley 32k 9 9 gold badges 77 77 silver badges bronze badges.
While I'm typically a proponent of Hamachi for this sort of thing I have to thank you for that link. The Routing and Remote Access service is installed automatically during the installation of Windows Server By default, however, the Routing and Remote Access service is turned off. Click the server icon that matches the local server name in the left pane of the console.
If the icon has a red circle in the lower-left corner, the Routing and Remote Access service hasn't been turned on. If the icon has a green arrow pointing up in the lower-left corner, the Routing and Remote Access service has been turned on. If the Routing and Remote Access service was previously turn on, you may want to reconfigure the server. To reconfigure the server:. Click to select VPN or Dial-up depending on the role that you intend to assign to this server.
In the IP Address Assignment window, click Automatically if a DHCP server will be used to assign addresses to remote clients, or click From a specified range of addresses if remote clients must only be given an address from a pre-defined pool.
In most cases, the DHCP option is simpler to administer. However, if DHCP isn't available, you must specify a range of static addresses. Click Next to continue. If you clicked From a specified range of addresses , the Address Range Assignment dialog box opens.
Click New. Type the first IP address in the range of addresses that you want to use in the Start IP address box. Windows calculates the number of addresses automatically.
Accept the default setting of No, use Routing and Remote Access to authenticate connection requests , and then click Next to continue. For the remote access server to forward traffic properly inside your network, you must configure it as a router with either static routes or routing protocols, so that all of the locations in the intranet are reachable from the remote access server.
The number of dial-up modem connections is dependent on the number of modems that are installed on the server. For example, if you have only one modem installed on the server, you can have only one modem connection at a time. The number of dial-up VPN connections is dependent on the number of simultaneous users whom you want to permit.
By default, when you run the procedure described in this article, you permit connections. To change the number of simultaneous connections, follow these steps:. You can also configure a static IP address pool. Configure the dial-in properties on user accounts and remote access policies to manage access for dial-up networking and VPN connections. To grant dial-in access to a user account if you're managing remote access on a user basis, follow these steps:.
If the VPN server already permits dial-up networking remote access services, do not delete the default policy. Instead, move it so that it is the last policy to be evaluated. To set up a connection to a VPN, follow these steps. To set up a client for virtual private network access, follow these steps on the client workstation:.
You will need to install a couple of software packages to enable this functionality. The instructions below were written for Ubuntu Ubuntu versions However, due to the large number of Linux versions available, it is not feasible to document every supported Ubuntu version. In order to begin the VPN setup, open a terminal window. Do this by searching for Terminal in your application list. Click on the Terminal icon to open a new session. Once the packages have been installed, you may open up the Network Settings by searching for Settings in the application list, or by clicking on the Network icon at the top right of the screen and selecting Wired or Wireless Settings.
If L2TP is not listed as an option, please see the first step about installing the required packages. Fill out the Name , Gateway , User name , and Password fields here. Note: To save your password on this screen, you must select the appropriate option from the question mark on the password field. Once the modal pops up, expand the Advanced options, and enter the following:.
Select OK to continue. You will be returned back to the Add VPN modal. Select the PPP Settings button.
0コメント